24 HOUR CALL OUTS | NO CALL OUT FEE
Tel: 07853 958388
24 HOUR CALL OUTS | NO CALL OUT FEE

Why Is Your Boiler Not Producing Hot Water? Causes, Checks and Fixes

Few things disrupt a cold Sheffield morning like stepping into a shower that never warms up. If you have a boiler not producing hot water, the cause is often simpler than you might expect, although some faults do need a qualified professional. At FH Plumbing & Gas Installations, we regularly help homeowners, tenants and landlords work out why their hot water has stopped, and this guide shares the practical knowledge we have built up from that work.

You will learn how your boiler heats water, the most common faults, which safe checks you can try yourself, and when it is time to call a Gas Safe registered engineer.

What Causes a Boiler Not Producing Hot Water?

The most common causes are low boiler pressure, a faulty diverter valve, a failed thermostat, a frozen condensate pipe, limescale build-up, or a fault with the hot water cylinder in a system boiler setup. Some of these are simple to rule out, while others involve gas appliances and must only be handled by a qualified engineer.

How Your Boiler Heats Your Water

Understanding the basics makes fault-finding far easier. Most Sheffield homes use one of three setups:

  • Combi boilers heat water on demand. When you open a tap, a plate heat exchanger warms the incoming mains water almost instantly.
  • System boilers heat water and store it in a separate hot water cylinder.
  • Regular (conventional) boilers work with a cylinder and a cold water tank, usually in the loft.

Because each setup works differently, the symptoms differ too. A combi boiler that stops producing hot water often has a different fault from a system boiler with a cylinder that stays cold.

Common Reasons for a Boiler Not Producing Hot Water

Low Boiler Pressure

Your boiler needs a certain water pressure to operate safely. If the pressure gauge reads below the recommended range, the boiler may lock out or limit hot water output. Pressure can drop after bleeding radiators or because of a small leak somewhere in the system.

A Faulty Diverter Valve

In a combi boiler, the diverter valve directs heat either to your radiators or to your taps. When it sticks or wears out, you might find the heating works perfectly while the taps run cold, or the other way round. This is one of the most frequent reasons for no hot water but heating still working.

Broken Thermostat or Temperature Settings

A faulty cylinder thermostat, or a boiler temperature set too low, can stop water reaching a comfortable temperature. Settings sometimes change after a power cut or a programmer reset, so they are worth reviewing.

Limescale on the Plate Heat Exchanger

Over time, mineral deposits can restrict flow through the plate heat exchanger. The result is lukewarm water or a slow rise in temperature, particularly when a tap is opened for a short time.

A Frozen Condensate Pipe

During a hard Sheffield winter, the plastic condensate pipe outside your home can freeze. When that happens, many modern condensing boilers shut down as a safety measure. You may see an error code or notice that the boiler has stopped altogether.

Pump, Ignition or Gas Supply Problems

A failing pump, an ignition fault or an interrupted gas supply can all leave you without hot water. These problems involve gas and electrical components, so they are for a qualified engineer only.

Cylinder or Immersion Heater Faults

If you have a hot water cylinder, a failed motorised valve or a tripped immersion heater could explain why the water stays cold even though the boiler fires up.

Safe Checks Before You Call an Engineer

If you spot a boiler not producing hot water, these quick checks are safe for most households and may save you a call-out:

  1. Check the display. Look for an error code and note it down. Your manual explains what it means.
  2. Review the pressure gauge. Most boilers should sit within the range shown in the manufacturer’s instructions.
  3. Confirm the thermostat and timer settings. Make sure hot water is switched on and the programmer is set correctly.
  4. Check other gas appliances. If your hob also seems to be off, there may be a wider supply issue.
  5. Look at the condensate pipe in freezing weather. If it is frozen, pouring warm (not boiling) water over it can sometimes help. Take care on icy ground.
  6. Try a single reset. If your boiler has a reset button, follow the manufacturer’s guidance and press it once only.

If none of these steps restores your hot water, stop there. Repeated resets or opening the boiler casing can make matters worse and may be unsafe.

Warning Signs That Need Urgent Attention

Some symptoms should never be ignored. If you notice any of the following, switch off the appliance and contact a Gas Safe registered engineer straight away:

  • A smell of gas (call the National Gas Emergency Service on 0800 111 999)
  • Yellow or orange flames instead of a steady blue flame
  • Black marks or soot around the boiler
  • Strange banging, whistling or gurgling noises
  • Visible leaks or water pooling beneath the unit
  • A carbon monoxide alarm sounding

Carbon monoxide is odourless and dangerous, so fitting a working alarm near your boiler is strongly recommended. If your alarm sounds, open windows, leave the property and seek emergency help.

Why DIY Gas Repairs Are Not Worth the Risk

It can be tempting to open the casing and investigate, but working on a gas appliance without the right qualifications is illegal as well as unsafe. A trained engineer uses calibrated equipment to test pressures, combustion and flow, and can spot issues that are invisible to the eye. A professional diagnosis also protects your warranty and keeps your home insurance valid.

What Happens During a Professional Repair Visit

When you book with FH Plumbing & Gas Installations, our engineer starts by listening to what you have noticed, including when the problem began and whether it affects the heating, the taps or both. We then carry out a methodical inspection, which typically covers pressure, the diverter valve, thermostats, flow rates and safety devices.

Once the cause of your boiler not producing hot water is identified, we explain the fault in plain English and give you a clear price before any work begins. Many problems can be resolved efficiently, and if a part is needed we will tell you honestly what is involved. If the fault looks urgent, our emergency plumbers in Sheffield can advise on the best next step, and you can read more about gas engineers in Sheffield to understand what a Gas Safe engineer checks.

Should You Repair or Replace Your Boiler?

Not every fault means a new boiler. As a general guide, repair usually makes sense when the boiler is under ten years old and the fault is isolated. Replacement may be worth considering when:

  • The boiler is 12 to 15 years old or more
  • Breakdowns are becoming frequent
  • Spare parts are hard to find
  • Your energy bills keep climbing
  • Repair costs are approaching the price of a newer unit

If a boiler not producing hot water keeps returning despite repairs, comparing options is sensible. Our guides on boiler replacement in Sheffield and boiler installation in Sheffield explain what to expect, and a modern high-efficiency model can also reduce running costs. If the fault turns out to be a leaking pipe or cylinder issue, our plumbers in Sheffield can help too.

How to Prevent Hot Water Problems in Future

A little regular care goes a long way:

  • Book an annual boiler service with a Gas Safe registered engineer.
  • Check the pressure gauge every month or so.
  • Insulate exposed pipes, especially the condensate pipe, before winter.
  • Bleed radiators when they feel cold at the top.
  • Run the heating briefly during warm months to keep components moving.
  • Act on early warning signs such as noises, slow heating or unusual smells.

Keeping on top of these habits makes a boiler not producing hot water far less likely, and it helps your system run efficiently year-round.

Frequently Asked Questions

Why is my boiler on but I have no hot water?

The boiler can be firing while a faulty diverter valve, thermostat or blocked heat exchanger prevents heat reaching your taps. A qualified engineer can identify which component is responsible.

Why do I have heating but no hot water?

This often points to a diverter valve problem on a combi boiler, or a cylinder, thermostat or motorised valve fault on a system boiler.

Can low pressure cause a boiler not producing hot water?

Yes. Low pressure can stop the boiler operating normally, and it may suggest a leak. If topping up the pressure does not help, or it keeps dropping, call an engineer.

Is it safe to keep using my boiler if the hot water stops?

If there is no gas smell, no carbon monoxide alarm and no leak, it is usually safe to leave the boiler off until it is checked. If you have any doubt, switch it off and seek advice.

How much does it cost to fix a boiler with no hot water?

The cost depends on the cause and the parts needed. A qualified engineer should explain the fault and provide a clear quote before starting work.

How often should my boiler be serviced?

Manufacturers generally recommend a service once a year, which helps catch small faults before they leave you cold.

Conclusion

A boiler not producing hot water is frustrating, but understanding the likely causes puts you in control. Start with the simple, safe checks, never ignore warning signs such as gas smells or carbon monoxide alarms, and leave anything involving the appliance itself to a qualified professional.

If your hot water has stopped and you would like friendly, honest advice, FH Plumbing & Gas Installations is ready to help homeowners, tenants and landlords across Sheffield. Call us on 07853 958388 or book a boiler repair visit today.

No Hot Water But Heating Works: Causes and Solutions

Waking up to a warm house but a freezing shower is one of the most frustrating boiler faults a homeowner can face. If you have no hot water but heating works, the good news is that your boiler is still firing, which usually points to a fault in one specific part of the system rather than a complete breakdown. In this guide, we explain the most common causes, the safe checks you can carry out yourself, and when it is time to call a Gas Safe registered engineer.

At FH Plumbing & Gas Installations, we regularly attend homes across Sheffield where the radiators are toasty but the taps run cold. The causes are usually straightforward to diagnose, and most can be fixed in a single visit.

Quick Answer: Why Is There Hot Heating but No Hot Water?

When a home has no hot water but heating works, the most common causes are a faulty diverter valve, a failed motorised valve, a stuck or broken thermostat, low boiler pressure, a scaled-up heat exchanger, or a problem with the hot water cylinder or its programmer settings. Homeowners often describe the same fault as no hot water but radiators are working, or simply heating works but no hot water. Because heating and hot water share one boiler but use different components to deliver heat, one can fail while the other carries on as normal.

Why Does Your Home Have No Hot Water But Heating Works?

Your boiler produces heat in the same way for both radiators and taps. The difference lies in where that heat is sent. Inside the system, valves and controls decide whether hot water goes to your radiators, to a cylinder, or directly to your taps. When one of those parts fails, you end up with a central heating working but hot water not working situation.

Understanding which type of boiler you own is the first step towards finding the fault.

Combi Boilers

A combi boiler heats water on demand. When you open a hot tap, the boiler switches from heating mode to hot water mode. If you have hot water not working on combi boiler models, the diverter valve is often the culprit, and it is the first part we check when a customer reports no hot water but heating works. This small valve redirects heat between the radiators and the taps, and when it sticks, the boiler keeps sending heat to the radiators only.

System and Regular Boilers

With a system or regular boiler, hot water is stored in a cylinder. If your boiler heating but no hot water is the problem here, the cause is often a stuck motorised (zone) valve, a failed cylinder thermostat, or a programmer that is not calling for hot water.

Common Causes of Hot Water Failure When the Heating Is Fine

1. Faulty Diverter Valve

On combi boilers, the diverter valve is one of the most frequent reasons for a boiler hot water problem. Signs include radiators heating up when you run a hot tap, or taps that only produce lukewarm water. Over time, limescale and debris can cause the valve to stick or its internal components to wear out.

2. Failed Motorised Valve

On system and regular setups, a two-port or three-port motorised valve directs hot water to the cylinder. If it jams, the cylinder never receives heat. You may notice the boiler firing for the radiators while the cylinder stays cold.

3. Thermostat or Programmer Problems

A cylinder thermostat that has failed, or a programmer set to heating only, can leave you with no hot water in house but heating is on, and a boiler not producing hot water even though it fires normally. It is worth checking your timer settings first, especially after a power cut or the clocks changing.

4. Limescale in the Heat Exchanger

Sheffield sits in a moderately hard water area, so scale can build up inside a combi boiler’s plate heat exchanger. The result is a boiler not heating water properly, with water that comes out lukewarm or fluctuates between hot and cold.

5. Low Boiler Pressure

If your boiler pressure drops below roughly 1 bar, some combi models prioritise safety and restrict hot water output. A gauge reading outside the normal range is a clear warning sign.

6. Airlocks or Blockages in Pipework

Trapped air or debris can stop hot water reaching the tap. If you notice no hot water from taps but heating works, and only one tap is affected, a localised blockage or tap fault may be to blame.

7. Cylinder or Immersion Heater Faults

If your home has a hot water cylinder, the immersion heater or thermostat could have failed. A cylinder that is fully cold while the boiler runs normally strongly suggests a control or valve fault.

Safe Checks You Can Do Before Calling an Engineer

Before you book a visit, there are a few simple steps worth trying. These are safe for any homeowner and can sometimes solve the problem without a call-out.

  1. Check the boiler display. Look for fault codes, and note them down for your engineer.
  2. Check the pressure gauge. If it is below 1 bar, your boiler manual will explain how to repressurise it safely.
  3. Review your programmer. Make sure hot water is switched on and scheduled correctly.
  4. Turn the hot water temperature up. Some combi boilers have a separate dial for domestic hot water.
  5. Run the hot tap for a minute. This can clear small airlocks and prompt the boiler to switch modes.
  6. Reset the boiler once. Follow the manufacturer’s instructions, and do not repeat the reset more than once.

If you still have no hot water but heating works after these checks, the fault is almost certainly a component that needs professional attention.

What Not to Do

Never remove the boiler casing, tamper with gas connections, or attempt to replace internal valves yourself. Gas appliances must be repaired by a Gas Safe registered engineer. If you smell gas, turn off the supply at the meter, open windows, avoid switches and flames, and call the National Gas Emergency line on 0800 111 999 straight away.

How a Professional Engineer Diagnoses the Problem

When you report no hot water but heating works, an experienced engineer follows a methodical process. They will check the pressure and fault codes, test the diverter or motorised valve, inspect the thermostat, measure flow rates at the tap, and assess whether limescale has restricted the heat exchanger. This structured approach avoids guesswork, which saves you money and prevents repeat visits.

At FH Plumbing & Gas Installations, our engineers explain what they find in plain English before any work begins, so you understand the fault, the repair options, and the cost involved. If your fault needs urgent attention, our emergency boiler repair service is available to help restore comfort quickly.

Repair or Replace: What Makes Sense?

Most cases of no hot water but heating works are repairable. A diverter valve replacement, a new motorised valve, or a thermostat swap is generally far more affordable than a new boiler. However, replacement may be worth considering if:

  • Your boiler is more than 12 to 15 years old
  • Repairs have become frequent or costly
  • Spare parts are no longer available
  • The heat exchanger is badly corroded or scaled

If you are weighing up your options, our team can advise honestly on whether a repair or a boiler installation is the better long-term investment for your home.

How to Prevent Hot Water Problems in the Future

Regular care keeps your system reliable throughout the year, especially through the colder months when demand is highest.

  • Book an annual boiler service. It is the single best way to catch worn valves and scale early.
  • Consider a magnetic filter or system flush. This removes sludge that can damage valves and heat exchangers.
  • Keep an eye on pressure. Top it up when needed and report repeated pressure loss.
  • Use a scale inhibitor in hard water areas. It helps protect combi heat exchangers.
  • Act on early warning signs. Lukewarm water, strange noises, or delayed hot water often appear before a full failure.

For wider pipework or tap-related concerns, our plumbing solutions cover everything from leaks to full system upgrades.

Frequently Asked Questions

Why do I have no hot water but heating works?

The usual causes are a faulty diverter valve, a stuck motorised valve, a failed thermostat, or limescale in the heat exchanger. Heating and hot water use different components, so one can fail while the other continues to work.

Is it safe to use my heating if the hot water has stopped working?

In most cases, yes, provided the boiler is not showing a safety fault, leaking, or producing unusual smells or noises. However, you should arrange an inspection promptly, because a stuck valve can worsen over time.

How much does it cost to fix a boiler that is not producing hot water?

Costs depend on the part and the make of the boiler. A diverter valve, motorised valve, or thermostat replacement are all common repairs, and a qualified engineer can give you a clear quote once the fault is confirmed.

Can low boiler pressure cause the boiler to stop heating water?

Yes. If pressure falls too low, many combi boilers restrict hot water output as a protective measure. Repressurising it safely can restore normal operation, but repeated drops suggest a leak that needs investigating.

How long does it take to fix a hot water fault?

Many faults can be diagnosed and repaired during a single visit if the engineer has the right part. More complex issues, such as a corroded heat exchanger, may take longer.

When should I call a professional?

Call an engineer if basic checks do not restore hot water, if the boiler shows repeated fault codes, or if your hot water stopped working suddenly with no obvious cause.

Conclusion: Get Your Hot Water Back Quickly

Having no hot water but heating works is stressful, but it is rarely a sign that your whole boiler has failed. A faulty diverter valve, a stuck motorised valve, a thermostat issue, or limescale is usually behind it, and each of these is fixable by a qualified professional. Start with the simple checks above, and never attempt internal gas repairs yourself.

If the problem persists, FH Plumbing & Gas Installations is ready to help with fast, honest, Gas Safe registered support. Get in touch through our contact or explore our emergency plumber near me service when you need help urgently.

Do You Need Plumbers? Call Us at 07853 958388

Call Now
Get A Quote