24 HOUR CALL OUTS | NO CALL OUT FEE
Tel: 07853 958388
24 HOUR CALL OUTS | NO CALL OUT FEE

No Hot Water But Heating Works: Causes and Solutions

Waking up to a warm house but a freezing shower is one of the most frustrating boiler faults a homeowner can face. If you have no hot water but heating works, the good news is that your boiler is still firing, which usually points to a fault in one specific part of the system rather than a complete breakdown. In this guide, we explain the most common causes, the safe checks you can carry out yourself, and when it is time to call a Gas Safe registered engineer.

At FH Plumbing & Gas Installations, we regularly attend homes across Sheffield where the radiators are toasty but the taps run cold. The causes are usually straightforward to diagnose, and most can be fixed in a single visit.

Quick Answer: Why Is There Hot Heating but No Hot Water?

When a home has no hot water but heating works, the most common causes are a faulty diverter valve, a failed motorised valve, a stuck or broken thermostat, low boiler pressure, a scaled-up heat exchanger, or a problem with the hot water cylinder or its programmer settings. Homeowners often describe the same fault as no hot water but radiators are working, or simply heating works but no hot water. Because heating and hot water share one boiler but use different components to deliver heat, one can fail while the other carries on as normal.

Why Does Your Home Have No Hot Water But Heating Works?

Your boiler produces heat in the same way for both radiators and taps. The difference lies in where that heat is sent. Inside the system, valves and controls decide whether hot water goes to your radiators, to a cylinder, or directly to your taps. When one of those parts fails, you end up with a central heating working but hot water not working situation.

Understanding which type of boiler you own is the first step towards finding the fault.

Combi Boilers

A combi boiler heats water on demand. When you open a hot tap, the boiler switches from heating mode to hot water mode. If you have hot water not working on combi boiler models, the diverter valve is often the culprit, and it is the first part we check when a customer reports no hot water but heating works. This small valve redirects heat between the radiators and the taps, and when it sticks, the boiler keeps sending heat to the radiators only.

System and Regular Boilers

With a system or regular boiler, hot water is stored in a cylinder. If your boiler heating but no hot water is the problem here, the cause is often a stuck motorised (zone) valve, a failed cylinder thermostat, or a programmer that is not calling for hot water.

Common Causes of Hot Water Failure When the Heating Is Fine

1. Faulty Diverter Valve

On combi boilers, the diverter valve is one of the most frequent reasons for a boiler hot water problem. Signs include radiators heating up when you run a hot tap, or taps that only produce lukewarm water. Over time, limescale and debris can cause the valve to stick or its internal components to wear out.

2. Failed Motorised Valve

On system and regular setups, a two-port or three-port motorised valve directs hot water to the cylinder. If it jams, the cylinder never receives heat. You may notice the boiler firing for the radiators while the cylinder stays cold.

3. Thermostat or Programmer Problems

A cylinder thermostat that has failed, or a programmer set to heating only, can leave you with no hot water in house but heating is on, and a boiler not producing hot water even though it fires normally. It is worth checking your timer settings first, especially after a power cut or the clocks changing.

4. Limescale in the Heat Exchanger

Sheffield sits in a moderately hard water area, so scale can build up inside a combi boiler’s plate heat exchanger. The result is a boiler not heating water properly, with water that comes out lukewarm or fluctuates between hot and cold.

5. Low Boiler Pressure

If your boiler pressure drops below roughly 1 bar, some combi models prioritise safety and restrict hot water output. A gauge reading outside the normal range is a clear warning sign.

6. Airlocks or Blockages in Pipework

Trapped air or debris can stop hot water reaching the tap. If you notice no hot water from taps but heating works, and only one tap is affected, a localised blockage or tap fault may be to blame.

7. Cylinder or Immersion Heater Faults

If your home has a hot water cylinder, the immersion heater or thermostat could have failed. A cylinder that is fully cold while the boiler runs normally strongly suggests a control or valve fault.

Safe Checks You Can Do Before Calling an Engineer

Before you book a visit, there are a few simple steps worth trying. These are safe for any homeowner and can sometimes solve the problem without a call-out.

  1. Check the boiler display. Look for fault codes, and note them down for your engineer.
  2. Check the pressure gauge. If it is below 1 bar, your boiler manual will explain how to repressurise it safely.
  3. Review your programmer. Make sure hot water is switched on and scheduled correctly.
  4. Turn the hot water temperature up. Some combi boilers have a separate dial for domestic hot water.
  5. Run the hot tap for a minute. This can clear small airlocks and prompt the boiler to switch modes.
  6. Reset the boiler once. Follow the manufacturer’s instructions, and do not repeat the reset more than once.

If you still have no hot water but heating works after these checks, the fault is almost certainly a component that needs professional attention.

What Not to Do

Never remove the boiler casing, tamper with gas connections, or attempt to replace internal valves yourself. Gas appliances must be repaired by a Gas Safe registered engineer. If you smell gas, turn off the supply at the meter, open windows, avoid switches and flames, and call the National Gas Emergency line on 0800 111 999 straight away.

How a Professional Engineer Diagnoses the Problem

When you report no hot water but heating works, an experienced engineer follows a methodical process. They will check the pressure and fault codes, test the diverter or motorised valve, inspect the thermostat, measure flow rates at the tap, and assess whether limescale has restricted the heat exchanger. This structured approach avoids guesswork, which saves you money and prevents repeat visits.

At FH Plumbing & Gas Installations, our engineers explain what they find in plain English before any work begins, so you understand the fault, the repair options, and the cost involved. If your fault needs urgent attention, our emergency boiler repair service is available to help restore comfort quickly.

Repair or Replace: What Makes Sense?

Most cases of no hot water but heating works are repairable. A diverter valve replacement, a new motorised valve, or a thermostat swap is generally far more affordable than a new boiler. However, replacement may be worth considering if:

  • Your boiler is more than 12 to 15 years old
  • Repairs have become frequent or costly
  • Spare parts are no longer available
  • The heat exchanger is badly corroded or scaled

If you are weighing up your options, our team can advise honestly on whether a repair or a boiler installation is the better long-term investment for your home.

How to Prevent Hot Water Problems in the Future

Regular care keeps your system reliable throughout the year, especially through the colder months when demand is highest.

  • Book an annual boiler service. It is the single best way to catch worn valves and scale early.
  • Consider a magnetic filter or system flush. This removes sludge that can damage valves and heat exchangers.
  • Keep an eye on pressure. Top it up when needed and report repeated pressure loss.
  • Use a scale inhibitor in hard water areas. It helps protect combi heat exchangers.
  • Act on early warning signs. Lukewarm water, strange noises, or delayed hot water often appear before a full failure.

For wider pipework or tap-related concerns, our plumbing solutions cover everything from leaks to full system upgrades.

Frequently Asked Questions

Why do I have no hot water but heating works?

The usual causes are a faulty diverter valve, a stuck motorised valve, a failed thermostat, or limescale in the heat exchanger. Heating and hot water use different components, so one can fail while the other continues to work.

Is it safe to use my heating if the hot water has stopped working?

In most cases, yes, provided the boiler is not showing a safety fault, leaking, or producing unusual smells or noises. However, you should arrange an inspection promptly, because a stuck valve can worsen over time.

How much does it cost to fix a boiler that is not producing hot water?

Costs depend on the part and the make of the boiler. A diverter valve, motorised valve, or thermostat replacement are all common repairs, and a qualified engineer can give you a clear quote once the fault is confirmed.

Can low boiler pressure cause the boiler to stop heating water?

Yes. If pressure falls too low, many combi boilers restrict hot water output as a protective measure. Repressurising it safely can restore normal operation, but repeated drops suggest a leak that needs investigating.

How long does it take to fix a hot water fault?

Many faults can be diagnosed and repaired during a single visit if the engineer has the right part. More complex issues, such as a corroded heat exchanger, may take longer.

When should I call a professional?

Call an engineer if basic checks do not restore hot water, if the boiler shows repeated fault codes, or if your hot water stopped working suddenly with no obvious cause.

Conclusion: Get Your Hot Water Back Quickly

Having no hot water but heating works is stressful, but it is rarely a sign that your whole boiler has failed. A faulty diverter valve, a stuck motorised valve, a thermostat issue, or limescale is usually behind it, and each of these is fixable by a qualified professional. Start with the simple checks above, and never attempt internal gas repairs yourself.

If the problem persists, FH Plumbing & Gas Installations is ready to help with fast, honest, Gas Safe registered support. Get in touch through our contact or explore our emergency plumber near me service when you need help urgently.

Do You Need Plumbers? Call Us at 07853 958388

Call Now
Get A Quote